DIY Tub Installation.
DIY Tub Installation.
Blog Article
How do you feel in regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bathtub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably difficult job. If the old tub is easily accessible, the project can move speedily; if you need to open a wall surface to eliminate the old tub and place the new bathtub, the job is much harder. In either instance, the project is within a residence handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the job as well as are comfortable trying it. Rather than hiring a specialist to take over a halfway-completed job, it is far better to think about utilizing one before you begin. Opportunities are you may require a professional plumber to make tube connections.
This write-up will aid you install a brand-new bathtub in your restroom if you have actually currently purchased a brand-new bathtub and don't need to alter the setup of your previous supply of water pipelines.
Your tools and product list should make up the following:
Getting ready for the Installment
Firstly, the supporting framework supplied with the bath must be fitted (if called for) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must now prepare to be suited its last setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you need to do is separate the water. After doing so, activate the faucets to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have actually been eliminated, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Installing the Bathtub
Making use of the two wood boards under its feet, put the bathtub in the called for position. The wood boards are valuable in equally spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four tiny factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level and also changing the feet on the bathtub till the level reads degree.
To install faucets, fit the bottom of the furthest versatile tap port to the appropriate supply pipeline by making a compression join; then do the exact same for the various other tap.
Activate the supply of water and also check all joints and also new pipework for leakages and tighten them if essential. Fill the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Ultimately, fix the bath paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the tub needs to wait until the tub has actually been used a minimum of when as this will settle it right into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin making certain that the washers are in place between the tap as well as the sink. Secure the tap in position with the supplier given backnut. Once the tap is safely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The previous kind needs to be attached to the faucet finishes first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bath satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to split a stiff seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, resulting in complications with dampness and also feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to permit the movement experienced when the tub is in usage. The sealant can break rather early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly readily available on the market. It is advisable to fit the ceramic tiles using water-resistant or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent person who reads on A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that excerpt was beneficial. Please take a moment to promote this blog post if you appreciated it. Many thanks for taking the time to read it.
Go Deal Now Report this page